Onicon D-100 Flow Manual do Utilizador descarregar pdf (Página 24)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Flow Display Manual 10/14 - 0634-14 / 18340 Page 24

Bi-directional Flow

Page No. Display Name Selectable Units

1 (+) Mode 1 Total Gal, Liter, M

, Ft

, lb mass, kg mass, SCF, NCM

2 (-) Mode 2 Total Gal, Liter, M

, Ft

, lb mass, kg mass, SCF, NCM

3 Flow Rate Ai2/Di2

GPM, GPH, MGD, l/s, l/min, l/hr, M

/hr, Ft

/m, lb/hr, kg/hr,

SCFH, SCFM, NCMH

4 Analog Input Ai3 DEG F, DEG C, PSI, BAR, KPASCL, GPM, L/S, M3/H, CFS, CFM,

KBTU/H, KW, TON, %RH, SCFM, SCFH, NCMH, None

5 Analog Input Ai4 DEG F, DEG C, PSI, BAR, KPASCL, GPM, L/S, M3/H, CFS, CFM,

KBTU/H, KW, TON, %RH, SCFM, SCFH, NCMH, None

6 Digital Input Di3 PULSE COUNT ONLY (Engineering units entered as text)

7 Alarm Status None

8 Serial Number None

4.3 UNITS AND MULTIPLIERS

The operating mode, engineering units and multipliers are programmed into the D-100 at the

factory. These settings may be re-programmed in the eld. Please contact ONICON for assistance

if changes are required.

4.4 ANALOG OUTPUTS

The D-100 is capable of providing up to four analog outputs (optional). Changing any of the

displayed units or multipliers will affect the analog outputs. If any unit or multiplier values are

changed at the D-100, the analog output value(s) will also be changed. If you are unsure of the

ramications of any changes you are contemplating, please contact ONICON for assistance.

4.5 ENABLING / DISABLING FRONT PANEL RESET

The table below explains how to enable or disable the FRONT PANEL RESET.

STEP ACTION REACTION COMMENT

1 With the display running, open the

front panel and locate DEV ADD/

PROG ENAB. Press DEV ADD/

PROG ENAB and then release it.

None DEV ADD/PROG ENAB is

located in the lower left

corner of the processor board.

(see appendix page A-2.)

2 Close the front panel.

3 Press the PROGRAM button. (If

you do not press the PROGRAM

button, the meter will revert to the

run mode after ve minutes.)

The display changes to program

mode and the DEVICE ID page will

appear with the rst digit of the

address ashing.

The PROGRAM button is on

the front panel.

4 Press the PROGRAM button. The FRONT PANEL RESET page

appears with the N or Y ashing.

5 Press the SCROLL button. The setting will toggle

between N and Y.

Enable or disable the FRONT

PANEL RESET as necessary.

6 Press the PROGRAM button. The SAVE CHANGES page appears

with the N ashing.

The new FRONT PANEL

RESET setting must be saved

to take effect.

7 Press the SCROLL button. The N changes to Y. The Y must be selected for the

change to take effect.

8 Press the PROGRAM button. The new setting is saved and the

display reverts to the run mode.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 34 35

Comentários a estes Manuais

Sem comentários

Onicon D-100 Flow Manual do Utilizador Página 24

Comentários a estes Manuais

Manuais e produtos relacionados com Instrumentos de medida Onicon D-100 Flow